羅茨鼓風機間隙調整方法：

　　Method for adjusting the clearance of Roots blower:

　　1、調整外殼間距：通過外殼和墻板定位銷孔來保證，這是因為在拆卸風機時不能損壞定位銷孔。葉輪-外殼0.20-0.395。

　　1. Adjust the spacing between the casing: This is ensured through the positioning pin holes on the casing and wall panels, as the positioning pin holes cannot be damaged when disassembling the fan. Impeller shell 0.20-0.395.

　　2、葉輪和葉輪間隙調整：將葉輪移動到間隙圖位置，將驅動齒輪標記與軸對齊，依次安裝齒輪擋圈、止動墊片和鎖緊螺母，稍微擰緊鎖緊螺母。如果葉輪不能轉動一圈，就旋轉葉輪進行接觸，用銅棒輕輕拍打葉輪間隙部位，使齒輪和圓錐體相互嚙合運動，達到調整葉輪間隙的目的。葉輪和葉輪間隙滿足指定值后，將齒輪鎖定到葉輪-葉輪0.29-0.34。

　　2. Adjustment of impeller and impeller clearance: Move the impeller to the clearance diagram position, align the drive gear mark with the shaft, install the gear retaining ring, stop washer, and locking nut in sequence, and slightly tighten the locking nut. If the impeller cannot rotate once, rotate the impeller to make contact, gently tap the gap between the impeller with a copper rod, and make the gear and cone mesh with each other to adjust the impeller gap. After the impeller and impeller clearance meet the specified value, lock the gear to impeller impeller 0.29-0.34.

　　3、葉輪和墻板軸向間距調整：組裝墻板時，應先確保軸向總間隙C 和 D(外殼密封厚度調整)，然后通過前墻板的4組調整螺釘調整葉輪軸位置，以確保兩端間距C和D的分布。葉輪-前壁面板0.12-0.18葉輪-后壁面板0.63-0.69調整螺栓時，壓板螺栓必須在松動的情況下進行。否則，調整螺栓可能會損壞。

　　3. Adjustment of axial spacing between impeller and wall panel: When assembling the wall panel, first ensure the total axial clearance C and D (adjusting the thickness of the shell seal), and then adjust the position of the impeller shaft through the four sets of adjustment screws on the front wall panel to ensure the distribution of the spacing C and D between the two ends. When adjusting the bolts of the impeller front wall panel 0.12-0.18 impeller rear wall panel 0.63-0.69, the pressure plate bolts must be loosened. Otherwise, adjusting the bolts may cause damage.

　　羅茨鼓風機出口堵塞引起的問題：

　　Problems caused by blockage of Roots blower outlet:

　　1、壓力計超壓

　　1. Pressure gauge overpressure

　　羅茨鼓風機安裝壓力表。前管堵塞時，羅茨鼓風機處于超壓狀態，壓力表自然表示超壓。這是最直接的表現。使用羅茨鼓風機時，如果發現這種情況，應立即進行停止處理，疏通管道后進行風機操作。

　　Install pressure gauge on Roots blower. When the front pipe is blocked, the Roots blower is in an overpressure state, and the pressure gauge naturally indicates overpressure. This is the most direct manifestation. When using a Roots blower, if this situation is found, it should be immediately stopped and the pipeline should be cleared before operating the blower.

　　2、風機溫度高

　　2. High fan temperature

　　增壓時，如果多半有這種現象，可以很容易地理解，羅茨風機強制輸送氣體，壓力過大的氣體釋放出更多的熱量，導致風機溫度過高，羅茨鼓風機的出口不堵塞，有時我們無法正常打開閘閥，導致增壓，鼓風機也有溫度過高的情況。

　　When boosting, if this phenomenon often occurs, it can be easily understood that the Roots blower forcibly delivers gas, and the gas with excessive pressure releases more heat, causing the fan temperature to be too high. The outlet of the Roots blower is not blocked, and sometimes we cannot open the gate valve normally, resulting in boosting. The blower also has a situation of high temperature.

　　3、電動機燃燒

　　3. Electric motor combustion

　　出口管道堵塞，羅茨鼓風機電機燃燒可能只需要一分鐘，在很短的時間內電機就會燃燒，燃燒后，只要機頭不破裂，就只能更換電機。

　　The outlet pipeline is blocked, and it may only take one minute for the Roots blower motor to burn. In a very short period of time, the motor will burn. After combustion, as long as the machine head does not break, the motor can only be replaced.

　　4、反轉風機

　　4. Reverse fan

　　出口堵塞，不能排除鼓風機壓縮進入的氣體，只能與葉輪相互作用，使鼓風機葉輪反向，這也是電動機燒毀的原因之一，葉輪使這臺電動機反向轉動，相互作用時電動機燒毀。

　　The outlet is blocked, and the compressed gas from the blower cannot be eliminated. It can only interact with the impeller, causing the blower impeller to rotate in the opposite direction. This is also one of the reasons for the motor burning out. The impeller causes the motor to rotate in the opposite direction, and the motor burns out during the interaction.

　　5、葉輪損壞

　　5. Damaged impeller

　　部分風機的葉輪質量不合格，電動機不燒，葉輪可能會壞，葉輪壞后瞬間被抱死，皮帶打滑，整個設備可能無法正常工作。

　　The quality of some fans' impellers is not up to standard, the electric motor does not burn, and the impellers may break. After the impellers break, they will be instantly locked, the belt will slip, and the entire equipment may not work properly.

　　本文由  三葉羅茨鼓風機 友情奉獻.更多有關的知識請點擊  https://http://m.baihengnewenergy.com  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Three Leaf Roots blower For more related knowledge, please click https://http://m.baihengnewenergy.com Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.